lura.

User hub

Store

All guides

Cronus Zen PS5 setup in 2026

Two ways to run the Zen on PS5, the free bypass or the Zen LINK module. The bypass step by step in under a minute, and the Zen LINK setup from Cronus's phone app with every PS5 setting and what its light means.

Lura Editorial · Sep 20, 2026 · Updated Nov 18, 2026 · 8 min read

There are two ways to run the Zen on a PS5. Zen LINK is Cronus's official module: set it up once and it connects on every boot. The PS5 bypass is free and needs only the Zen, but it is unofficial and you repeat it each time the console restarts. Both work. Which one suits you comes down to money against convenience.

The two ways

Zen LINK PS5 bypass
Cost The module, or the PS5 Ultimate Edition bundle Free
Official Yes, Cronus's supported method No, a community workaround Cronus does not support
Every boot Connects by itself Redo the bypass after each PS5 restart
After a PS5 system update Keeps working Can stop working until a new method is found
Needs A phone with the Zenlink app and Wi-Fi with a 2.4 GHz band; a Windows PC once for an original V1 Nothing extra
Controller port Module in A1, controller in A2 or A3, or paired to the Zen by Bluetooth Controller in the Zen as usual

Without either one, Cronus's own guide is plain: the controller disconnects from the PS5.

If you use the bypass, keep the PS5's automatic system updates switched off, so an update does not arrive the night before you want to play.

The PS5 bypass

Check before every bypass

  • Communication method is Use USB Cable. Settings, Accessories, Controllers (General), Communication Method. A PS5 update can switch it back.
  • Bluetooth is on, and your DualSense has been paired to the PS5 wirelessly at least once. Settings, Accessories, General.
  • Nothing else on Bluetooth. Disconnect any other Bluetooth device from the PS5: headsets, a second controller, anything.
  • Nothing plugged into the controller. No headset in the jack, no extras on the pad.
  • The Zen is in PS5 mode. Its screen shows the gearhead logo; if not, press the right blue button until it does.
  • No script running. Put the Zen on slot 0 while you do the bypass; select your script afterwards.

Every time the PS5 starts

  1. Controller into A1 on the Zen, with a data cable.
  2. Unplug the cable from the top of the Zen, the console cable that runs to the PS5. Leave the other end in the PS5.
  3. On the PS5, go to Settings, Accessories, General and hover over Turn Off Accessories. Do not press X.
  4. Plug the cable back into the top of the Zen, then straight away hold right on the D-pad. Keep holding for about five seconds. The PS5 menu flickers as the Zen works through it, then the Zen's screen flashes and returns to the gearhead logo.
  5. Let go, press Circle to back out, select your script's slot on the Zen, and play.

If it does not take, unplug the top cable and do steps 3 to 5 again; it often works on the second try. If a rear USB port on the PS5 will not take it, use a front one. After a PS5 restart, rest mode or unplugging the controller, it needs doing again.

Cronus's own bypass page, read on 18 November 2026, runs the last steps in a slightly different order, worth trying when the one above will not take. It plugs the Zen into a front USB port on the PS5, opens Turn Off Accessories and highlights your controller in that list, then holds right on the D-pad first and keeps holding while the cable goes back into the Zen, for about five seconds.

Zen LINK now runs in what Cronus calls PS5 Native Mode. The module goes on the Zen's A1 port, you set it up once from Cronus's Zenlink phone app, and from then on it connects with no bypass and no Remote Play setup. The steps, settings and light meanings below are Cronus's, from its Zen Link setup and status light pages, read on 18 November 2026.

What you need

Item Note
Zen on the current 2.4.x firmware Firmware update guide
Zen LINK module, a V2 or an upgraded V1 In the Zen's A1 port; the model is printed on the label underneath
DualSense or DualSense Edge In A2 or A3 with a data cable, or paired to the Zen by Bluetooth
A short data cable, Zen to PS5 Charge-only cables do nothing
A phone with Cronus's Zenlink app From the iOS App Store or Google Play, with Bluetooth on
Wi-Fi with a 2.4 GHz band Zen LINK is a 2.4 GHz device, and the phone joins the same network
A Windows PC, original V1 only Once, for Cronus's upgrade

Which model you have

A V2 module says V2 on the label underneath; the original module does not mention V2 anywhere. An original V1 needs Cronus's one-time upgrade before the steps below. Plug it in while holding its blue Config button, open Cronus's ZenLinkConfigurator on a Windows PC, enter your Wi-Fi details and choose Native Mode. The update starts once it reaches the Wi-Fi, and after it the V1 works like a V2 and keeps itself updated.

Steps

  1. Firmware first. Update the Zen to the latest 2.4.x.
  2. Wire it. Zen's CONSOLE/PC port to the PS5. Zen LINK into A1. Controller into A2 or A3. When the Zen powers the module, its light turns blue.
  3. Set it up from your phone. Install the Zenlink app, turn on the phone's Bluetooth, and join the Wi-Fi you want the module on, which has to have a 2.4 GHz band. The app finds the module over Bluetooth and takes your Wi-Fi details. Setup is done when the app opens on its CRONUS ZenLink main screen.
  4. Change the PS5 settings, table below.
  5. Watch the light. It shows magenta while PS5 Native Mode starts, then three light-green flashes once it is up. Play.
  6. Load your script if you have not: how to put a script on the Zen. Select the slot and test every button in the console menu before a match.

Zen LINK updates its own firmware over Wi-Fi, starting about 30 seconds after it connects, with no app or cable involved. A fast-blinking blue light is an update running; leave the module plugged in until it finishes.

The PS5 settings

Menu Setting Value
System, Power Saving Set Time Until PS5 Enters Rest Mode, While Playing Games Don't Put in Rest Mode
System, Power Saving, Features Available in Rest Mode Supply Power to USB Ports Always
System, Power Saving, Features Available in Rest Mode Stay Connected to the Internet Enable
System, Power Saving, Features Available in Rest Mode Enable Turning On PS5 from Network Enable
System, Power Saving Set Time Until Controllers Turn Off Don't Turn Off
Accessories, Controller (General) Vibration Intensity Strong (Standard)
Accessories, Controller (General) Trigger Effect Intensity Strong (Standard)
Accessories, Controller (General) Communication Method Use USB Cable
Accessories, General, Advanced Settings Bluetooth Off

Communication Method is the one Cronus singles out: without Use USB Cable the PS5 cannot connect through the Zen and the module at all. Bluetooth is the setting that differs from the bypass, which needs it on. Guides written for the older Zen LINK setup also had you enable Remote Play and console sharing; Cronus's current list leaves both out.

On a DualSense Edge the controller settings above sit under Profile 1, and Cronus wants the right stick left at its defaults, since changed values break many of its mods. Make a custom profile under Settings, Accessories, DualSense Edge Wireless Controller, Custom Profiles, Create Custom Profile, and set Right Stick Sensitivity Curve to Default, Curve Adjustment to 0 and Deadzone Adjustment to 0%.

What the module's light means

Cronus reads the light by colour and rhythm. Red always means something failed, and it blinks in groups: count one group before the pause.

Light Meaning
Solid blue Setup mode: no working Wi-Fi yet, so finish setup in the Zenlink app
Blue, slow fade or blinking once a second Joining the Wi-Fi
Two green flashes On the Wi-Fi
Two orange flashes A Wi-Fi problem
Dim white, steady Idle and healthy
Magenta PS5 Native Mode starting
Three light-green flashes Native Mode is up
Blue, fast blinking Firmware update running
Red, quick blips Native Mode did not start; it clears in about ten seconds, then try again
Red, long blinks The module has stopped and will not recover by itself
Dark No power

When it drops

Symptom Fix
Drops after the console slept Rest mode to Don't Put in Rest Mode while playing; wake it; power-cycle the Zen
Controller switches off Set Time Until Controllers Turn Off to Don't Turn Off
No connection to the PS5 at all Communication Method to Use USB Cable
App shows Connection Failed The phone is on another network, or the network has no 2.4 GHz band; join the same Wi-Fi, switch mobile data off for a moment, press Try Again
App cannot find the module Module powered, phone on the same network, 2.4 GHz still on at the router; press Retry
No sound in a headset on the pad A 3.5 mm headset needs the pad wired to A2 or A3; over Bluetooth it gets no audio
Red long blinks Note the colour, the speed and the number of blinks before the pause, and send them to Cronus support
Light stays dark Another USB port or cable

For a timing script, keep the pad wired to A2 or A3 rather than on Bluetooth. Wired or wireless explains why.

Questions

Does the Cronus Zen work on PS5 without Zen LINK?
Yes, with the PS5 bypass. It is free and works on the Zen alone, but it is unofficial, has to be redone every time the PS5 restarts, and a PS5 system update can break it. Zen LINK is the official route and needs no bypass.
Do I need to buy Zen LINK?
No. It is optional. It saves you the bypass on every boot and is the method Cronus supports. Plenty of players use the bypass instead.
How does Zen LINK connect to the PS5?
Through what Cronus calls PS5 Native Mode. The module sits in the Zen's A1 port, joins your Wi-Fi on its 2.4 GHz band, and is set up once from Cronus's Zenlink phone app. A V2 module needs no PC; an original V1 needs a one-time upgrade from a Windows PC first.
Which controller do I use?
A DualSense or DualSense Edge for every feature. With Zen LINK the module takes A1 and the pad goes in A2 or A3 with a data cable, or pairs to the Zen by Bluetooth, though a headset in the pad's jack only works while the pad is wired.
What does the Zen LINK light mean?
Solid blue is setup mode, waiting for Wi-Fi details from the app. Dim white is idle and healthy. Magenta means PS5 Native Mode is starting, and three light-green flashes mean it worked. Red blinks in groups you count; quick ones clear by themselves in about ten seconds, long ones mean the module has stopped.
How long does the bypass take?
About a minute once you know it. Controller in A1, Zen on slot 0, unplug the cable from the top of the Zen, hover over Turn Off Accessories, plug the cable back in and straight away hold right on the D-pad for about five seconds.
Why does it disconnect after a while?
With Zen LINK, usually rest mode, the controller timeout, or the Wi-Fi. With the bypass, usually a PS5 restart, which means doing the bypass again.